APPLICATION
The LVC 5050 is a general purpose, high voltage, medium continuous current, linear power amplifier. It works best when driving loads of 2 - 16 ohms. The LVC 5050 works well with either pulsed or continuous test signals or enviroments that have both conditions. The LVC 5050 has two (2) seperate channels that can be operated independently or combined for greater maximum voltage current. In Bridge-Mono mode the available output voltage doubles. In Parallel-Mono mode the amplifier operates with twice the available output current.

FEATURES
> Bi Level TM Power Supply, amplifier optimizes itself for either, high voltage/low current or low voltage/high current,
dynamically. This feature allows the LVC 5050 to produce less heat, have higher long term power, with no added distortion.
> Output of 20.0 amperes rms, or 106 volts rms, per channel depending on load.
> Frequency bandwidth of DC to 20 kHz at full power.
> Controlled Voltage or Controlled Current operation
> User-adjustable voltage or current limiting
> Remote force to standby mode by contact closure
> External buffered monitoring of voltage and current output
> Protection provided against, input overloads, improper output connection (including shorts and improper loads), excessive temperature, voltage or current, and under voltage conditions.
> Shipped ready to operate using single-phase, 120-volt AC mains. Also available in 100, 200, 208, 230 and 240 VAC
versions.
> Installs easily into a standard 19 inch rack, or stands alone for bench top operations

OPTIONS – User Configurable
> Variable voltage and current limiting
> DC Coupled (DC enabled) or AC coupled (DC Blocked)
> Controlled Voltage or Controlled Current operation
> In Voltage mode - Fixed gain (20, 71, 132) or Variable (0 – 20, 0-71, 0 – 132)
> In Current mode - Fixed Trans-conductance (20) or Variable (0 – 20)
>Channel configuration – two independent channels, two channels paralleled to Mono, two channels bridged to Mono

OPTIONS – Factory Only Configurable
> Shipped ready to operate using single-phase,
Available in 100V 30Amp, 120 Volt 30 Amp, 200V 15Amp, 220V- 240V 15 Amp, all configurations 50/60Hz

INDICATORS AND CONTROLS
> Front panel LEDs indicate signal presence and output overload
> A pushbutton power “On/Off” located on the front panel
> Two gain controls on the front panel for controlled voltage applications
> A back panel slide switch to choose between 2 channel, bridge mono and parallel mono operation

OUTPUT POWER
Measurements taken at 1 kHz at .05% THD with amplifiers operating in controlled voltage mode.

PERFORMANCE (One hour continuous ratings)
Frequency Response
. +/- 0.1 dB from 20 Hz to 20 kHz at 1 watt.
Phase Response
. +/- 10 Degrees (10 Hz to 20 kHz at 1 watt).
Signal-to-Noise Ratio
. At Voltage gain of 20, better than 105 dB (A-weighted) below full output.
THD
. Less than 0.05% from 20 Hz to 1 kHz increasing linearly to 0.1% at 20 kHz
at full output.
I.M. Distortion
. < 0.05% from 410 milliwatts to full output with a voltage gain of 20 into
an 8 ohm load.
Slew Rate
. >31V per microsecond.
Load Impedance
. Rated for 16, 8, 4 and 2 ohm use. Safe with all load types, including reactive loads
Input Impedance
. Greater than 10K ohms, balanced, and 5K ohms unbalanced.
Output Impedance
. Less than 10 milliohms in series with less than 2 microhenries.

PHYSICAL CHARACTERISTICS
Chassis: The Amplifier is designed for stand alone, or rack mounted, operation. The Chassis is black steel with a silver
finished aluminum front panel. The unit occupies three EIA 19-inch-wide units.
Weight: 77 lbs. (35.2 kg), Shipping 95 lbs. (43.2 kgs)
AC Power: Single phase, 120 volts, 60 Hz, 30 amperes ac service. (Note: 100, 120, 200, 208, 230 or 240 volt, 50-60 Hz
models are available, call for specifications.) US models come with 3 blade NEMA TT30P plug.
Cooling: Forced air cooling from the front, through removable filters, to the back.
Dimensions: 19 in. x 16 in. x 5.25 in (48.3 cm x 40.3.0 cm x 13.3 cm)

SUPPORT
When you purchase an AE Techron amplifier, a full complement of technical and factory support personnel join your team. AE Techron provides:
> Applications engineering for your technical questions and customizedproduct needs.
> A one year limited warranty to protect your equipment investment.
> A fully equipped service center to keep your amplifier operating at original performance requirements.