LVC623 Amplifier Specifications
APPLICATION
The LVC 623 is a general purpose, medium voltage, high continuous current, linear power amplifier. It works best when driving loads of 1 - 4ohms. The LVC 623 works well with continuous test signals. The LVC 623 has two (2) separate channels that can be operated independently or combined for greater maximum voltage or current. In bridge-mono mode the available output voltage doubles. In parallel-mono mode the amplifier operates with double the output current.

FEATURES
> Output of 13.0 amperes rms, or 26 volts rms, per channel into a 2 ohm load.
> Frequency bandwidth of DC to 20 kHz at full power.
> Option of controlled voltage, or controlled current operation, modes changed via a jumper.
> User-adjustable voltage or current limiting.
> Remote switching to standby mode by contact closure.
> External monitoring of voltage and current output.
> Equipped with circuitry to protect the amplifier from input overloads, improper output connection (including shorts and improper loads), excessive temperature, voltage or current.
> Shipped ready to operate using single-phase, 120-volt AC mains.
> Installs easily into a standard 19 inch rack, or stands alone for bench top operations.

INDICATORS AND CONTROLS
> Front panel LEDs indicate signal presence and output overload.
> A pushbutton power “On/Off” located on the front panel.
> Two gain controls on the front panel for controlled voltage applications.
> Two circuit breaker resets on the back panel.
> A back panel slide switch to lift signal ground from chassis ground.
> A back panel slide switch to choose between 2 channel, bridge mono and parallel mono operation.
OUTPUT POWER
Measurements taken at 1 kHz at .05% THD with amplifiers operating in controlled voltage mode.
PERFORMANCE (One hour continuous ratings)
Frequency response
. +/- 0.1 dB from DC to 20 kHz at 1 watt.
Phase response
. +/- 10 Degrees (10 Hz to 20 kHz at 1 watt.
Signal-to-noise ratio
. At 26 dB gain, better than 105 dB (A-weighted)below full output.
THD
. Less than 0.05% from 20 Hz to 1 kHz increasing
. linearly to 0.1% at 20 kHz at full output.
I.M. Distortion
. <0.05% from 410 milliwatts to full output at 26dB gain with an
. 8 ohm load.
Slew rate
. >13V per microsecond.
Load Impedance
. Rated for 16, 8, 4, 2 and 1 ohm use. Safe with allload types even
. reactive ones.
Input Impedance
. Greater than 10K ohms, balanced, and 5K ohms unbalanced.
Output impedance
. Less than 10 milliohms in series with less than 2 microhenries.
One Channel Driven
40mSec Burst
1 Hour Continuous
Ohms
Watts
Volts
Amps
Watts
Volts
Amps
2
354
27
13
354
26.59
13
4
240
31
8
242
31.1
8
8
148
34
4
145
34
4
16
89
38
2
89
37.78
2
Two Channel Bridged to Mono
40mSec Burst
1 Hour Continuous
Ohms
Watts
Volts
Amps
Watts
Volts
Amps
4
538
46.40
12
538
46.4
12
8
431
58.70
7
431
58.7
7
16
290
68.10
4
290
58.1
4
Two Channel Paralleled to Mono
40mSec Burst
1 Hour Continuous
Ohms
Watts
Volts
Amps
Watts
Volts
Amps
1
520
22.8
23
520
22.8
23
2
420
29
14
418
28.9
14
4
290
34
9
289
34
9
8
166
36
5
165
36.3
5
PHYSICAL CHARACTERISTICS
Chassis: The Amplifier is designed for stand alone, or rack mounted, operation. The Chassis is black steel with a silver
finished aluminum front panel. The unit occupies two EIA 19-inch-wide units.
Weight: 55 lbs. (25 kg), Shipping 66 lbs. (30 kg)
AC Power: Single phase, 120 volts, 60 Hz, 15 amperes ac service.
Cooling: Forced air cooling from the front, through removable filters, to side panels.
Dimensions: 19 in. x 16 in. x 3.5 in (48.3 cm x 40.3.0 cm x 8.9 cm)

SUPPORT
When you purchase an AE Techron amplifier, a full complement of technical and factory support personnel join your team. AE Techron provides:
> Applications engineering for your technical questions and customizedproduct needs.
> A one year limited warranty to protect your equipment investment.
> A fully equipped service center to keep your amplifier operating at original performance requirements.

Copyright AE Techron, Inc. 2007 Report site problems to the webmaster.